15 Square Meters Mobile Phone Signal Detector Detecting 2G 3G 4G
Please Contact with us at:
Mr.Jerry
Product introduction: The appearance of the new generation of T9000 detectors is made of military-quality alloys, with the addition of a code-based LED display, which can more accurately indicate the intensity of the signal source, and the led flashlight on the back The function of the section is more intimate in designing the lighting requirements under special circumstances. U.S. Army Using technology, it is an exclusive research and development of a variety of bugs for the market, car trackers, mobile phones lying Bottom software, wireless pinhole camera, surveillance camera, casino fraud cheating equipment, etc., oriented Developed security category instruments. The product fully satisfies the military/police detection function in this field Simultaneously Quantitative detection of electrical radiation sources protects you and your family from electromagnetic radiation. This product Taking the lead in adopting the digital acceptance model, unlike the products on the market, not only broadens the frequency of exploration, but also Effectively avoid the interference of products in the ubiquitous messy signal in life The new generation T9000 is a portable wireless signal and magnetic field detection device, especially for CDMA The special processing of signals, the CDMA mobile phone protocol is a wireless frequency hopping technology invented by the US military. The full name (code division multiple access) has a small transmission power. Conventional radio wave detectors cannot be detected CDMA signals, and the tracking locators on the market mostly use CDMA cards and WCDMA cards, because This T9000 is your best choice.
First, the panel and function: the device is handheld, as shown in the figure: 1. The top left side is the antenna interface. Please install the antenna when using the device. 2. The middle is the magnetic probe interface, and the magnetic probe is mostly used to detect the hidden position of the magnetic locator and the eavesdropper Strong magnetic products. 3. headphone jack, can be connected to headphones, more concealed and convenient 4. Window Azimuth dial, window with special filter lens, scanned by LED infrared laser technology Hidden hidden wired or wireless camera equipment. 5. LED display (code-type signal strength indicator, power display) 6. Vibration, ring mode switch button, can be viewed on the left side of the LED display 7.strong magnetic detection switch, when using LED display, the red light is on under standby mode. 8. Camera detection switch Four-speed adjustment, right side of LED display 9. LED flashlight light switch to adjust the light intensity like right rotation 10.USB charging port 11. Power and sensitivity adjustment switch 12. the back LED flashlight lamp beads 13. back infrared scanning lamp beads Tip: The charging indicator will automatically turn off when the battery is fullI.
Instructions for use:
Turn the knob clockwise to the maximum,"BIBI' long sound, the machine enters the detection mode. LED main screen lights up to indicate normal operation
RF wireless signal detection
Turn on the switch and adjust the knob to the first stage of the signal strength pointer to enter the standby mode. The code-type signal strength indicator is divided into ten levels, which are white, green, yellow and red, "White safety signal ""Green suspicious signal" Yellow danger signal" and the final red lock signal source)
During normal detection, first adjust the pointer to the white part of the LED display, that is, between one and two levels. If any in a strong signal environment ,the pointer will fluctuate back and forth, and the buzzing alarm will be open .The closer the suspicious object is, the higher the number of levels pointed to by the pointer(finally pointing to the 10-levels red area is to lock ). Fixed suspicious by target) .The closer the hazard signal is to the vibration frequency, the more the vibration frequency will gradually increase, and finally the suspicious signal source is locked with an uninterrupted vibration prompt.
3. The detection range can be set according to the adjustment sensitivity knob. The higher the level of adjustment, the wider the range (such as When the red zone is turned to the buzzer alarm is not working, the pointer has no fluctuation, that is, there is no signal in a wide range .State) Special reminder: in the metropolitan environment, the signal source is messy and needs to adjust the sensitivity knob to gradually Troubleshoot suspicious signal.
* Due to the high sensitivity of the product, you can receive mobile phone base station TV broadcasts everywhere on the roads in urban areas. Signal, so it is recommended to search the car for tracking, locator, please drive the car to the signal source relative Operate in a weaker place and turn off the device that has the wireless transmit source function, such as a mobile phone
*If there is an alarm action when opening the device in the room where there is no suspicious object, there are several possibilities 1. body's own communication equipment timing automatically and base station code 2. suspicious objects in the next door, or someone in the next door is talking 3. is too close to the wireless router(the above situation can also be detected by adjusting the sensitivity knob)
Magnetic field signal detection Install the magnetic probe, turn on the power, press the strong magnetic detection switch, the purple indicator on the top of the magnetic probe After the light is on, Ienter the magnetic field signal detection standby state, and the magnetic field Induction probe is close to the magnetic field source, before the probe The white LED of the terminal LED lights up and the buzzer alarm will work, indicating that there is a magnetic field or magnetic field near the magnetic probe. Strong Imagnetic suspicious items exist
Camera detection Explore hidden wired or wireless standby camera devices, turn on the power, and press the camera to detect Off, the scanning function is turned on at this time. the laser scanning light on the back flashes, and the frequency stops in the fourth gear .Scan in the fixed range of the window through a special filter, if a suspicious red reflective spot is found The position of the hidden wireless camera device can be gradually determined by adjusting the laser flicker frequency from fast to slow. (The flashing frequency of the fourth gear is the fastest, and the scanning Frequency setting can be more comfortable according to individual needs
Brief description of the detection of automotive strong magnetic adsorption equipment: Magnetic locators and eavesdroppers are mostly used in cars, and most of the a dsorption positions are hidden in the bottom of the car, or inside the car. The concealed area is spatially isolated from the surface of the car body, so it is not recommended to directly detect and build outside the car body . Discuss in the car, the bottom of the car, or open the front and rear covers of the vehicle, and perform a gridded close-range exploration. It is easy to find a strong magnetic adsorption device.
Scope of application: 1. Whether a wireless bug or tracker is installed in a car or office or business negotiation place 2. Whether the mobile phone is eavesdropped or abnormal (the signal is emitted outside without any reason during standby 3. Working environment, whether there is base station radiation around the house 4. Check hotel restrooms, hotels, bathing rooms, changing rooms, entertainment venues, school invigilation, military facilities, etc 5. Radio waves on the mahjong table coincident with the action 6.Mortgage vehicles, used cars, pawn shops, guarantee companies, microfinance companies, information finance and other companies
Technical indicators: Frequency range: IMHZ-8000MHZ Detection dynamic range: >73DB Detection sensitivity: ≤0.03mv(main frequency band) Detection range: 2.4G: 10 square meters (standard 10mw) 1. 2G: 15 square meters (standard 10mw) Mobile phone band 2G 3G 4G Signal: 15 square meters 10-level digital tube, buzzer, vibrator indication Power: Built-in 1200mA polymer lithium battery, full charge time 3 hours Working current: 80-150mA Continuous working time: 8-10 hours Material: ABS plastic Weight: 210g Volume: 115mm*60mm*23mm
Product packaging content: 1, the host 1 2, antenna 1 3, the magnetic probe 1 4.a pair of headphones 1 5. a copy of the manual 1 The above four, please check if unpacking, The specific color parameters of the product are subject to the actual product.